No results were found for the filter!
Magnet holder Kit
Magnet holder Kit for for Brackets, IR Temperature sensor and Weather Station. It consists of magnet, Screw, nut M8 and washer.
Power-switch Cable for MCC15
This Power Cable is needed when power to GNSS receiver is taken via the "CB2" Box.
Cables, Straight CAN connection 1m
Cable with straight connectors at both ends. Connectors: 7-pin Bay. - 7-pol Bay.
Power Cable "Xsite PRO / Xsite PRO ADVANCED"
Power Cable for Xsite PRO / Xsite PRO ADVANCED Operating Panel.
Power Cable GS-506 Controller
Power cable for power supply of controller/system "GS-506". Cable length: 6 Meter Connectors: 7 pin screw connection to open end
Y-Coil Cable, R-30cm/6m Connection
Y-Coil cable, R-30 cm / 6 m connection between controller, machine and slope sensor Cable length: 6 Meter (stretched) / 0.3m incl. 1 x 120 Ohm CAN bus resistor Connectors: CA 10 pole male coupling (controller), CA 10 pole female...
Coil Cable, 3 m Connection Sonic/Machine, 6-pin...
6 pin Connection Coil cable to connect the Sensor Sonic-Ski with the Machine.
Coil Cable, Connection Sonic/Machine, 5-pin
5 pin Connection Coil cable to connect the Sensor Sonic-Ski with the Machine.
Coil Cable, 6m Connection Controller/Sensor
Cable length: 6m (stretched) Connectors: CA 7pole, male, CA 7pole, female
USB Adapter Cable
USB Adapter Cable to connect "MOBA-Drive" to a "Windows Office" PC Connectors: USB-A, 4-pin female
Adapter Cable, CA/M12
Adapter, CA Bayonet/M12 with 120 Ohm bus resistor Wire cross section: 5 x 0.34mm² Connectors: 5 pin M12, male, 7 pin bay, female
Power Cable for On-board Computer "MOBA...
Power connection for On-board computer "MOBA Operand". Cable Length: 8 Meter Wire cross section: 4 x 0.75 mm² Connector: 7 pin "Fischer", female automobile power connector
CAN Cable for On-board Computer "MOBA Operand",...
CAN connection cable for On-Board Computer "MOBA Operand"
Cable-set "Weather Station"
Cable set "Weather Station" Application: Pave-IR System Consisting of: 04-02-15353 Cable A, 0.5 Meter, 10 pin (weather station) / 7 pin "Binder", male 04-02-15352 Cable B, 5 Meters, 5 pin male, M12 / 7 pin "Binder", fem.
Connection Cables Duo Level III
Connection Cable to connect sensor with built-in indicator Connector: 7-pin, female, Open end
Connection Cables for Duo Level IV
Connection Cable to connect sensor with built-in indicator (Duo Level IV) Connector: 7-pin, female, 7-pin, male
Coil Cable, Extension 6 m Connection...
Coil cable, exten. 6m connection from controller to sensor cable (CAN-interface)
Coil Cable, Connection Junction/Sensor...
Coil cable, 6m connection from junction box to the sensor (CAN-interface) Cable length: 6 m (stretched) Connectors: CA 7-pin, bay. male, CA 7-pin, bay. female
Coil Cable, 3m Connection Controller/Machine,...
For individual connection to machine Cable length: 3 Meter (stretched) Connectors: CA 12 pin bay. female (to conroller), Open end
Coil Cable, 3m Connection Controller/Machine
Cable length: 3 Meter (stretched) Connectors: CA 12 pin bay. female (to conroller), CA 10 pole bay, female (to machine)
Coil Cable, 3m Connection Controller/Machine...
Cable length: 3 Meter (stretched) Connectors: CA 12 pole bay. female (to conroller), CA 10 pole, female (to machine)
Coil Cable, 6 m Connection Controller/Sensor
Cable Type: CAN-interface incl. 2 x 120 Ohm CAN bus resistor Cable length: 6 Meter (stretched) Connectors: CA 7 pole bay. male, CA 7 pole bay. female
Coil Cable, Extension 6m Connection...
Cable length: 6 Meter (stretched) Connectors: CA 7 pin, male, CA 7 pin, female coupling
Coil Cable, 6m Connection Controller/Machine
Cable length: 6 Meter (stretched) Connectors: CA 7 pole, male, CA 7 pole 90°, female coupling
Coil Cable, 6 m Connection Controller/Machine...
Cable length: 6 Meter, (stretched) Connectors: CA 7 pole 90° female open end
Coil Cable, 6m Connection Controller/Machine...
Cable length: 6 Meter, (stretched) Connectors: CA 7 pin 90° female, CA 10 pin female
Coil Cable, 3 m Connection Controller/Machine...
Connectors: CA 7 pole 90° female, CA 10 pole female
'Y-Cable, MCA-500', 3/1m
Connection for Power supply and CAN to operating panel "GDC-320". Cable length: 3 Meter (Power), 1 Meter (CAN) Connectors: 7 pin Binder, female (GDC-320), 5 pin Binder M12, female (CAN), Open end
Y-Cable, CA-M12 Cable Junction
Cable length: 30 cm Connectors: 1 x CA 10 pole male couppling to 1 x CA 10 pole female, 1 x M12 5 pole female
Y-Coil Cable, 30cm/6m Connection Cable
Y-coil cable, 30 cm / 6 m connection between digital controller V3.26, machine and Sonic-Ski CAN and/or junction box. Cable length: 6 Meter (stretched) / 0,3 m incl. 2 x 120 Ohm CAN bus resistor Connectors: 10 pin male coupling...
Y-cable, M12
Cable junction Cable length: 30 cm Wire cross section: 5 x 0.34mm² Connectors: 1 x 5 pin M12, male, 2 x 5 pin M12, female
Cable M12, CAN, 5 m incl. 120 Ohm CAN-Bus-Resistor
Cable length: 5 Meter Connectors: 5 pole M12, male, 5 pole M12, female
Bus Termination Cable, M12 120 Ohm Resistor
Cable length: 30cm Wire cross section: 5 x 0,34mm² Connectors: 5-pin M12, male, 5-pin M12, female
Antenna Cable Set "SMART Antenna"
Cable set "Smart antenna" Application: Pave-IR System Consisting of: 04-02-15348 Cable A, 0.8 m, 14 pole(antenna) / 7 pole "Binder", male 04-02-15351 Cable B, 5 m, 5 pole male, M12 / 7 pole "Binder", fem.
Ignition Box IS-01
Ignition box for automatic Gas ignition and flame control on asphalt paver screeds
Coil Cable 6m
M12 Connection
Power-switch
Y-Coil Cable
Coil Cable
Power Cable
Magnet holder
RS232 Data
Coil Cable
Coil Cable 3 m
USB Adapter
Coil Cable 3 m
Y-Cable CA-M12
Power Cable
Y-Coil Cable
Cables Straight
Coil Cable 3m
Ignition Box
Coil Cable
GNSS Antenna
Coil Cable 3m
Bus Termination
Standard Cables
Antenna Cable
RS-232 to USB
USB Data Cable
Power Cable
Cable 5 m
Adapter Cable
Y-cable M12
GNSS Antenna
Coil Cable
Cable M12 CAN 5
Coil Cable 6 m
Satel Cable for
Connection
Ignition Cables
CAN Cable for
Coil Cable 3m
Cable-set
Coil Cable 3 m
Ignition Box
Cable Machine
Coil Cable
Power Cable
Y-Cable MCA-500
Viewed